KT Tourniquet Carrier

Can be carried by itself, attached the KT Gunfighter/Defender or KT AKELA holsters.

KT Drop Leg - for the KT Gunfighter/Defeder or any OWB holster

Universally attach any OWB holster

Turn your hip holster into a Drop Leg

IMP Closed Belt Loops

Fits 1.75" and 1.5" belts

Easy mechanical cant adjustment.

Compatible with the KT Gunfighter/Defender holsters, not compatible with the KT AKELA holsters.

IMP Low Profile Belt Loops

These Low Profile belt loops are ideal for back quarter carry, as well as small of back OWB carry, or on your side if you are a larger individual. Fits both 1.5" to 1.75" wide belt.

Warning! If you plan to carry the holster on your side, the best option is the Standard belt loops. These Low Profile loops will make the holster too wide and may cause stress fractures on the holster if you try to force them to bend to your body. This will void the warranty.

Warning! Not recommended for the KT Defender holster since the KT Defender will have the added width of a weapon light. The KT Defender holster will already sit very close to your body. The best option is the Standard belt loops. These Low Profile loops will make the holster too wide and may cause stress fractures on the holster if you try to force them to bend to your body. This will void the warranty.

Compatible with the KT Gunfighter/Defender holsters, not compatible with the KT AKELA holsters.

Metal Clips (IWB/OWB) KT Gunfighter/Defender

IWB: Hardened Steel Spring Metal Clips for IWB carry. These metal clips are available in pairs for the KT Gunfighter/Defender holster. For IWB carry, they are installed on the front of the holster and can be clipped on without the need to undo and loop your belt through. These are made of hardened steel, some elbow grease may be required when donning.

OWB: Hardened Steel Spring Metal Clips for OWB carry. These metal clips are available in pairs for the KT Gunfighter/Defender holster. For OWB carry, these metal clips will include the Offset Blocks and they go on the back (your body side) of the holster. Notice the mounting screw configuration from the picture above. The Offset Blocks can be removed so that you can use the metal clips for IWB carry. These are made of hardened steel, some elbow grease may be required when donning.

Fits up to 1.75" belts. Wider belt sizes will also work, however the clips will be pressing on the material rather than capturing the belt as shown on the image above.

IWB Soft Loops (Convertible to Soft OWB loops)

The IWB Soft Loops are made of a durable and flexible material. Unlike leather, they will not swell when wet so they are Maritime ready. Heavy Duty snaps are included. Be sure to use non-permanent thread locker (blue) when you find your preferred setup, to prevent the screws from loosening.

Fits up to 1.75" belts.

Includes: 1 pair (2 ea)

IWB Jhooks - Tuckable

The IWB Jhooks will allow you to carry the KT Gunfighter/Defender holsters concealed and with your shirt tucked in. These IWB Jhooks can also be installed for a lowered carry for Deep Concealment.

Warning! For IWB concealed carry only, not for OWB use. The IWB Jhooks are for deep concealment which will bring the holster lower inside the pants. For a standard ride height IWB setup with a full grip draw, please choose the IWB Metal Clips or the IWB soft loops instead.

Warning! Because the JHooks are commonly misused, these JHooks are non-refundable and have no warranty.

Fits up to 1.75" belts.

Includes: 1 pair (2 ea)

KT FLEXMOUNT™ MOLLE webbing or VELCRO attachment

The KT FLEXMOUNT™ will allow you to attach the KT Gunfighter/Defender holster onto MOLLE/PALS webbing or VELCRO (both hook or loop surface). Ideal for attaching the holster on Battle/War MOLLE belts and VELCRO.

Includes: 1 pair (2 ea)

KT Active Retention Strap

Easy, inexpensive, functional level 2 retention. Works with any KT Holster.

Custom Laser Engraving service

Requirements:

1st - Submit your image design or text. The image will have to be Black/White only (no gray) as show on the sample.

You must be the owner of the image or permission from the image creator or a Licensee.

Attach to email - contact@kt-mech.com

2nd - Indicate where you'd like us to engrave your design or text (max. size approx. 1/8 the surface area of the holster).

Simply download the template (save onto your computer), open with any drawing program and draw a red box where you'd like your image or txt engraved then email it back to us.

3rd - Make a payment.

Choose the "Engraved solid" option if you are submitting a B/W image with no gray scale.

Choose the "Text only" option if you are submitting an text.

The Custom Laser Engraving service is a "Service" not a "Product" so it is non-refundable.

Non-permanent Thread Locker service

applied to all attached parts - great if you're not planning to change your setup

Fasteners - Binding Posts / Screws / Spacers